AJA V2Analog Specifications Page 22
- Page / 90
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
14
CVBS Composite NTSC/PAL Output
One BNC connector supplies composite NTSC or PAL output. Connect the
CVBS Out BNC to a monitor, or other Composite video device. Composite
video signals are D/A (output) converted (10-bit).
Note: Composite video output follows the settings made for the component video output;
because of this, if a composite output is desired when working with HD, the component
video output must be set to SD.
HDMI
Two HDMI connectors provide for input and output of HDMI compatible
video (version 2.0) and multi-channel embedded audio. HDCP is not
supported on either input or output. The HDMI input is designed to support
long cable runs: up to 100 feet (30.48m) when using 22 or 24AWG HDMI cable, or up
to 50 feet (15.24m) using 28 or 30AWG HDMI cable. The HDMI output supports
standard HDMI cables only.
HDMI Formats supported in Version 2.0:
525i 29.97
625i 25
720p 50, 720p 59.94
1080i 25, 1080i 29.97,
1080p 23.98, 1080p 24, 1080p 25, 1080p 29.97
Note: When using Ki Pro HDMI connections and attaching it to any HDMI audio or video
accessory, you must use one each of the ferrite beaded HDMI cables, HH-28F-06, between
the input and output ports of the Ki Pro and the HDMI accessory to maintain regulatory
compliance.
Analog 2 Channel Balanced Audio Input and Output
Four XLRs, 2 female for input and 2 male for output, provide 2
channels of balanced audio. Audio is high-quality 24-bit A/D
input and D/A output at 48kHz. Level adjustments are made via
software and a switch for line-level inputs. Software level
adjustments for analog audio (parameter 4.1) apply to balanced
audio (XLR) using the “Line” setting on the switch. The Mic and
Mic +48 settings offer a lower input level suitable for
microphones and their associated input impedance. Use
Mic +48 for microphones with phantom power (condenser mic.), or Mic for
microphones without phantom power (dynamic micrphones).
Analog 2 Channel Unbalanced Audio Input and Output
Two RCA connectors provide an unbalanced stereo audio input pair for use with
consumer camcorders, VTR/VCRs and other A/V devices. For output, two RCA
connectors provide an unbalanced stereo audio output pair for driving inexpensive
audio monitoring systems.
9-pin Connector
Ki Pro features a 9-pin serial port that may be used with some RS-422
devices beginning with the 2.0 version of firmware. IMPORTANT: Not all
RS-422 devices have been tested with Ki Pro, so AJA cannot definitively say which
devices may or may not communicate as expected with Ki Pro when operated under
RS-422 remote control. Refer to the latest Release Notes document for which devices
or non-linear editors have been tested with Ki Pro operating under RS-422 control.
- Installation and Operation 1
- Limitation of 3
- Liability 3
- Table of Contents 5
- Chapter 1: Introduction 9
- Features 10
- Software 11
- What’s In The Box? 13
- Chapter 2: Getting Started 15
- Operator Side 16
- ADJUSTSELECT 17
- Displays and Indicators 19
- Other Front Panel Features 19
- Connector Side 20
- LTC Timecode Input And Output 21
- SDI Input and Outputs 21
- Component YPbPr 21
- 9-pin Connector 22
- ExpressCard/34 24
- Memory Cards 24
- Firewire 800 25
- Connector 25
- Power connector 25
- (AC Adapter) 25
- Installation 26
- Camera Mounting 27
- Using AC Power 31
- Using DC Power 31
- Remote Network Control 32
- TCP/IP Information 33
- Yo u’ll Need 33
- Networking via 33
- Networking Ki Pro 34
- TRANSPORT Mode 39
- TRANSPORT Mode (default) 40
- Recording Notes 41
- STATUS menus 43
- INVALID SELECTION 44
- UNRECOGNIZED MEDIA 44
- MEDIA IN USE 44
- MEDIA menus 45
- 16.2 DELETE CLIPS 46
- 17.0 REEL NAME 46
- 17.2 CLIP NAME 46
- Clip Naming—Two Examples 46
- 17.3 CLIP NUMBER 1 to 999 47
- (default = 1) 47
- 17.4 CLIP APPEND 48
- 17.5 ALPHA APPEND 48
- 17.8 TAKE 48
- Custom Clip 48
- 19.1 USE CUSTOM CLIP NAME 49
- 19.2 CUSTOM CLIP NAME 49
- 19.3 USE CUSTOM CLIP TAKE 49
- 19.4 CUSTOM TAKE 49
- Slave Name 50
- 1.1 RECORD TYPE 51
- 1.3 1080p PLAYBACK 51
- 1.4 IN CONVERT 52
- 1.5 OUT CONVERT 52
- 1.6 SDI OUT 52
- 1.7 COMPONENT OUT 52
- 1.8 HDMI OUT 52
- 2.1 VIDEO INPUT 53
- 2.2 AUDIO INPUT 53
- 2.3 AUDIO CHANNELS 53
- 3.1 COMPONENT IN LVL 53
- 3.2 COMPONENT OUT LVL 54
- 3.4 NTSC CONFIG 54
- 4.1 ANALOG AUDIO 54
- 5.1 UPCONVERSION 55
- 5.2 DOWNCONVERSION 56
- 6.1 GENLOCK 56
- 8.0 TC IN 56
- 8.1 TC VALUE 57
- 8.2 TC TYPE 57
- 8.3 ARM RECORDING 57
- 35.2 9-PIN REMOTE 57
- 41.1 VIDEO SG FRMT 58
- 41.2 VIDEO SG 58
- 41.3 AUDIO SG 59
- 50.1 IP CONFIG 59
- 50.2 IP ADDRESS 59
- 50.3 SUBNET MASK 60
- 50.4 STATIC GATEWAY 60
- 50.5 SYSTEM NAME 60
- 50.6 MAC ADDRESS 61
- 50.7 802.11 MAC ADDRESS 61
- 53.0 802.11 AVAILABLE 61
- 53.1 802.11 CONTROL 62
- 53.2 802.11 NETWORK 62
- 53.3 802.11 SECURITY 63
- 53.4 802.11 PASSWORD 63
- 53.5 HIDE 802.11 PASSWORD 63
- 54.1 802.11 IP CONFIG 63
- 54.2 802.11 IP ADDRESS 64
- 54.3 802.11 SUBNET MASK 64
- 55.4 DATE SET 64
- 70.2 DISPLAY INTENSITY 65
- 55.6 TIME SET 65
- 70.1 SCREEN SAVER 65
- 70.3 FAN SPEED 66
- 80.1SERIAL NUMBER 66
- 80.2 SW VERSION 66
- 99.0 FACTORY RESET 66
- Browser Remote Control 67
- General Screen 68
- Information 68
- Controlling Multiple 68
- Example: 69
- How to Use Gang Recording 69
- Resetting Values To 71
- Factory Settings 71
- Update Firmware 81
- Preparing to Update Software 81
- Appendix A: Specifications 87
© 2020, manymanuals.com. All rights reserved. | 3.353 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals