AJA V2Analog Specifications Page 66
- Page / 90
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
58
70.3 FAN SPEED
This parameter determines the speed of Ki Pro’s internal cooling fan. In some
environments where audio recording is occurring close to the Ki Pro unit, it may be
desirable to set the fan speed to “QUIET RECORD” for optimum quiet operation.
80.1SERIAL NUMBER
This parameter displays this Ki Pro’s unique serial number.
80.2 SW VERSION
This parameter displays Ki Pro’s software version level.
99.0 FACTORY RESET
Selecting this parameter and then pressing the ADJUST (up) button for 2 seconds
recalls
Ki Pro’s factory default settings.
Caution!
Selecting this parameter and recalling factory defaults will overwrite the current
settings (with the exception of network settings, which are retained).
Recalling factory defaults does not affect these network settings: IP
Config, IP Address, Subnet Mask, Default Gateway, System Name, 802.11 settings, or
Date and Time. To clear network settings and recall factory defaults, hold down both
the Adjust (up) and Adjust (down) buttons at the same time.
Note: To set a single parameter to its factory default value, go to that parameter and hold
down both the Adjust (up) and Adjust (down) buttons at the same time.
70.3 FAN SPEED NORMAL (DEFAULT)
NORMAL AUTO
QUIET RECORD
QUIET AUTO
Fan runs at normal fixed speed for optimum cooling.
Fan runs at variable speeds for optimal cooling.
Fan runs at a fixed slower speed for optimum quiet.
Fan runs at normal speed until recording begins, then the
fan ramps down to a slower speed for optimum quiet.
- Installation and Operation 1
- Limitation of 3
- Liability 3
- Table of Contents 5
- Chapter 1: Introduction 9
- Features 10
- Software 11
- What’s In The Box? 13
- Chapter 2: Getting Started 15
- Operator Side 16
- ADJUSTSELECT 17
- Displays and Indicators 19
- Other Front Panel Features 19
- Connector Side 20
- LTC Timecode Input And Output 21
- SDI Input and Outputs 21
- Component YPbPr 21
- 9-pin Connector 22
- ExpressCard/34 24
- Memory Cards 24
- Firewire 800 25
- Connector 25
- Power connector 25
- (AC Adapter) 25
- Installation 26
- Camera Mounting 27
- Using AC Power 31
- Using DC Power 31
- Remote Network Control 32
- TCP/IP Information 33
- Yo u’ll Need 33
- Networking via 33
- Networking Ki Pro 34
- TRANSPORT Mode 39
- TRANSPORT Mode (default) 40
- Recording Notes 41
- STATUS menus 43
- INVALID SELECTION 44
- UNRECOGNIZED MEDIA 44
- MEDIA IN USE 44
- MEDIA menus 45
- 16.2 DELETE CLIPS 46
- 17.0 REEL NAME 46
- 17.2 CLIP NAME 46
- Clip Naming—Two Examples 46
- 17.3 CLIP NUMBER 1 to 999 47
- (default = 1) 47
- 17.4 CLIP APPEND 48
- 17.5 ALPHA APPEND 48
- 17.8 TAKE 48
- Custom Clip 48
- 19.1 USE CUSTOM CLIP NAME 49
- 19.2 CUSTOM CLIP NAME 49
- 19.3 USE CUSTOM CLIP TAKE 49
- 19.4 CUSTOM TAKE 49
- Slave Name 50
- 1.1 RECORD TYPE 51
- 1.3 1080p PLAYBACK 51
- 1.4 IN CONVERT 52
- 1.5 OUT CONVERT 52
- 1.6 SDI OUT 52
- 1.7 COMPONENT OUT 52
- 1.8 HDMI OUT 52
- 2.1 VIDEO INPUT 53
- 2.2 AUDIO INPUT 53
- 2.3 AUDIO CHANNELS 53
- 3.1 COMPONENT IN LVL 53
- 3.2 COMPONENT OUT LVL 54
- 3.4 NTSC CONFIG 54
- 4.1 ANALOG AUDIO 54
- 5.1 UPCONVERSION 55
- 5.2 DOWNCONVERSION 56
- 6.1 GENLOCK 56
- 8.0 TC IN 56
- 8.1 TC VALUE 57
- 8.2 TC TYPE 57
- 8.3 ARM RECORDING 57
- 35.2 9-PIN REMOTE 57
- 41.1 VIDEO SG FRMT 58
- 41.2 VIDEO SG 58
- 41.3 AUDIO SG 59
- 50.1 IP CONFIG 59
- 50.2 IP ADDRESS 59
- 50.3 SUBNET MASK 60
- 50.4 STATIC GATEWAY 60
- 50.5 SYSTEM NAME 60
- 50.6 MAC ADDRESS 61
- 50.7 802.11 MAC ADDRESS 61
- 53.0 802.11 AVAILABLE 61
- 53.1 802.11 CONTROL 62
- 53.2 802.11 NETWORK 62
- 53.3 802.11 SECURITY 63
- 53.4 802.11 PASSWORD 63
- 53.5 HIDE 802.11 PASSWORD 63
- 54.1 802.11 IP CONFIG 63
- 54.2 802.11 IP ADDRESS 64
- 54.3 802.11 SUBNET MASK 64
- 55.4 DATE SET 64
- 70.2 DISPLAY INTENSITY 65
- 55.6 TIME SET 65
- 70.1 SCREEN SAVER 65
- 70.3 FAN SPEED 66
- 80.1SERIAL NUMBER 66
- 80.2 SW VERSION 66
- 99.0 FACTORY RESET 66
- Browser Remote Control 67
- General Screen 68
- Information 68
- Controlling Multiple 68
- Example: 69
- How to Use Gang Recording 69
- Resetting Values To 71
- Factory Settings 71
- Update Firmware 81
- Preparing to Update Software 81
- Appendix A: Specifications 87
© 2020, manymanuals.com. All rights reserved. | 0.548 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals