AJA V2Analog Specifications Page 67
- Page / 90
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
1
1
Chapter 4: Browser Remote Control
4
Remote Control Overview
An optimized web server inside Ki Pro allows you to remotely monitor and adjust parameter
settings via a a browser client, either running on a network wired computer or wireless device.
The network can be a closed local area network, a straight computer-to-Ki Pro cable, or even
exposed through a firewall to a broadband WAN (not generally recommended since anyone
on the internet can then access the Ki Pro). If wireless networking is desired, Ki Pro can
communicate with a LAN attached 802.11 access point for communication with wireless
browser clients like an Apple iPhone or Apple iPod Touch—or 802.11b/g enabled laptops.
The LAN connection on Ki Pro uses a standard RJ45 connector, but internally it’s intelligent
and communicates via standard “straight-through” CAT 5 ethernet cables or null-modem
(cross-over) cables without any configuration or strapping required.
Note: Safari is the supported web browser for Ki Pro control. Other browser software may
work, but AJA cannot guarantee operation.
Web Browser via Ethernet
To control Ki Pro via wired internet, connect a computer to the Ki Pro unit’s LAN connector, an
RJ45 socket, via a CAT5 ethernet cable.
To access the Ki Pro, simply enter its URL in the web browser. The URL will be the IP address
defined in Ki Pro’s Network parameter menus (50.2—please note also that 50.1 through 50.4
must all be configured correctly to access Ki Pro on your network). If Ki Pro is using DHCP (the
default), the IP address can be found by going to parameter 50.2 and reading it there. When
Ki Pro is shipped from the AJA factory, it defaults to DHCP operation.
If 50.1 is set to DHCP, and the DHCP server on the network fails to grant an IP address, then Ki
Pro will fall back to the static IP address.
If 50.1 is set to Default Addr, the factory default static IP address is: 10.65.74.65.
So, if 50.1 is set to Default Addr, you would type the following in the web browser:
http://10.65.74.65 to see Ki Pro’s web interface Main Status screen.
- Installation and Operation 1
- Limitation of 3
- Liability 3
- Table of Contents 5
- Chapter 1: Introduction 9
- Features 10
- Software 11
- What’s In The Box? 13
- Chapter 2: Getting Started 15
- Operator Side 16
- ADJUSTSELECT 17
- Displays and Indicators 19
- Other Front Panel Features 19
- Connector Side 20
- LTC Timecode Input And Output 21
- SDI Input and Outputs 21
- Component YPbPr 21
- 9-pin Connector 22
- ExpressCard/34 24
- Memory Cards 24
- Firewire 800 25
- Connector 25
- Power connector 25
- (AC Adapter) 25
- Installation 26
- Camera Mounting 27
- Using AC Power 31
- Using DC Power 31
- Remote Network Control 32
- TCP/IP Information 33
- Yo u’ll Need 33
- Networking via 33
- Networking Ki Pro 34
- TRANSPORT Mode 39
- TRANSPORT Mode (default) 40
- Recording Notes 41
- STATUS menus 43
- INVALID SELECTION 44
- UNRECOGNIZED MEDIA 44
- MEDIA IN USE 44
- MEDIA menus 45
- 16.2 DELETE CLIPS 46
- 17.0 REEL NAME 46
- 17.2 CLIP NAME 46
- Clip Naming—Two Examples 46
- 17.3 CLIP NUMBER 1 to 999 47
- (default = 1) 47
- 17.4 CLIP APPEND 48
- 17.5 ALPHA APPEND 48
- 17.8 TAKE 48
- Custom Clip 48
- 19.1 USE CUSTOM CLIP NAME 49
- 19.2 CUSTOM CLIP NAME 49
- 19.3 USE CUSTOM CLIP TAKE 49
- 19.4 CUSTOM TAKE 49
- Slave Name 50
- 1.1 RECORD TYPE 51
- 1.3 1080p PLAYBACK 51
- 1.4 IN CONVERT 52
- 1.5 OUT CONVERT 52
- 1.6 SDI OUT 52
- 1.7 COMPONENT OUT 52
- 1.8 HDMI OUT 52
- 2.1 VIDEO INPUT 53
- 2.2 AUDIO INPUT 53
- 2.3 AUDIO CHANNELS 53
- 3.1 COMPONENT IN LVL 53
- 3.2 COMPONENT OUT LVL 54
- 3.4 NTSC CONFIG 54
- 4.1 ANALOG AUDIO 54
- 5.1 UPCONVERSION 55
- 5.2 DOWNCONVERSION 56
- 6.1 GENLOCK 56
- 8.0 TC IN 56
- 8.1 TC VALUE 57
- 8.2 TC TYPE 57
- 8.3 ARM RECORDING 57
- 35.2 9-PIN REMOTE 57
- 41.1 VIDEO SG FRMT 58
- 41.2 VIDEO SG 58
- 41.3 AUDIO SG 59
- 50.1 IP CONFIG 59
- 50.2 IP ADDRESS 59
- 50.3 SUBNET MASK 60
- 50.4 STATIC GATEWAY 60
- 50.5 SYSTEM NAME 60
- 50.6 MAC ADDRESS 61
- 50.7 802.11 MAC ADDRESS 61
- 53.0 802.11 AVAILABLE 61
- 53.1 802.11 CONTROL 62
- 53.2 802.11 NETWORK 62
- 53.3 802.11 SECURITY 63
- 53.4 802.11 PASSWORD 63
- 53.5 HIDE 802.11 PASSWORD 63
- 54.1 802.11 IP CONFIG 63
- 54.2 802.11 IP ADDRESS 64
- 54.3 802.11 SUBNET MASK 64
- 55.4 DATE SET 64
- 70.2 DISPLAY INTENSITY 65
- 55.6 TIME SET 65
- 70.1 SCREEN SAVER 65
- 70.3 FAN SPEED 66
- 80.1SERIAL NUMBER 66
- 80.2 SW VERSION 66
- 99.0 FACTORY RESET 66
- Browser Remote Control 67
- General Screen 68
- Information 68
- Controlling Multiple 68
- Example: 69
- How to Use Gang Recording 69
- Resetting Values To 71
- Factory Settings 71
- Update Firmware 81
- Preparing to Update Software 81
- Appendix A: Specifications 87
© 2020, manymanuals.com. All rights reserved. | 1.603 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals