AJA Ki PRO rack Specifications Page 34
- Page / 111
- Table of contents
- BOOKMARKS
Rated. / 5. Based on customer reviews
Ki Pro Rack v4.2 www.aja.com
34
Alarm Status
The Alarm menu displays warnings and alarms. Some alarms will automatically be shown
on the display. Others will only be seen by checking the STATUS displays (press Select up/
down to cycle through them). If everything is OK, a “SYSTEM NORMAL” message will be
seen when you cycle through the STATUS displays.
You will be alerted to an alarm condition by having all backlit keys and the display flash
to full intensity for 2 seconds. If more than one alarm state is active, the display holds
each alarm notification for 3 seconds before cycling to the next alarm. These alarm
notifications override whatever the display is currently showing for the TRANSPORT or
STATUS menus. Once there is a Ki Pro Rack alarm active (e.g. Invalid Selection) the STATUS
button light blinks for as long as the alarm is present. This alerts you so you’ll know the
reasons for the alarm condition are still active. You can then press the STATUS button to
determine what the alarm condition is.
CONFIG and MEDIA menus, once entered after an alarm notification, will cause the alarm
display to go away. Pushing any button always returns Ki Pro Rack to its pre-alarm state—
however, if the alarm condition still exists after this initial button push (i.e., the reason for
the alarm), the alarm notification will reappear on the display. Note: the STATUS button
will blink if there is an active alarm condition.
Examples of ALARM displays are shown following this page. WARNING appears on the
first line and the prompted action item on the second line.
Ki Pro Rack features a variety of alarms to help you diagnose the condition of the unit,
possible configuration issues, or possible signal issues. Here is a list of warning messages
and their meanings:
"WARNING Input Format Changed" prompt appears if a recording is started and the
signal is lost or changed. If this occurs, Ki Pro Rack stops the recording in progress unless
the Loss of Video CONFIG parameter is set to continue recording.
"WARNING Record Format" may appear if there is no video input to Ki Pro Rack. No
recording will be performed in this state.
"WARNING A/V Mismatch" may appear if SDI video is selected and HDMI audio is selected
or vice versa. Embedded audio, via SDI or HDMI, must be matched to the video source.
Analog audio can be used with any video input.
SYSTEM NORMAL
WARNINIG
INVALID SELECTION
WARNING
UNRECOGNIZED MEDIA
WARNING
MEDIA IN USE
- Version 4.2 1
- Published: September 30, 2013 1
- Table of Contents 2
- Trademarks 6
- Copyright 6
- Contacting Support 6
- Chapter 1: Introduction 7
- Features 8
- Apple ProRes 422 Advantages 9
- Avid DNxHD Advantages 9
- In This Manual 10
- Overview 11
- Operator Side 12
- Displays and Indicators 14
- Connector Side 15
- 422 devices 16
- Removable Storage 18
- Modules (HDD or 18
- Using Ki Pro Media 19
- Rack in Final Cut Pro 19
- Using Ki Pro Rack 20
- Media with Avid 20
- Media Composer 20
- Chapter 3: Installation 21
- What’s In The Box? 22
- Remote Network Control 24
- TCP/IP Information 25
- You’ll Need 25
- Networking via 25
- Networking Ki Pro 26
- Mac Ping Procedure 28
- TRANSPORT Mode (default) 30
- Recording Notes 32
- STATUS menus 33
- Alarm Status 34
- MEDIA menus 36
- Data-LAN 37
- Considerations 37
- 14.0 ENCODE MODE 37
- 14.1 ENCODE TYPE 38
- 15.1 PLAY MEDIA 38
- 15.2 LOOP PLAY 38
- 15.3 PLAYLIST 38
- 15.4 DROPPED FRAMES 38
- Custom Clip 41
- CONFIG menus 43
- 1.1 RECORD TYPE 44
- 1.3 1080p PLAYBACK 44
- 1.4 IN CONVERT 44
- 1.5 OUT CONVERT 45
- 1.6 SDI OUT 45
- 1.6 SDI 2 OUT 45
- 1.7 COMPONENT OUT 45
- 1.8 HDMI OUT 45
- 1.9 SUPER OUT 46
- 2.1 VIDEO INPUT 46
- 2.2 AUDIO INPUT 46
- 2.3 AUDIO CHANNELS 46
- 3.1 COMPONENT IN LVL 47
- 3.2 COMPONENT OUT 47
- 3.4 NTSC CONFIG 47
- 4.1 ANALOG AUDIO 47
- 4.2 AUDIO LVL L 48
- 4.3 AUDIO LVL R 48
- 5.1 UPCONVERSION 48
- 5.2 DOWNCONVERSION 49
- 6.1 GENLOCK 50
- 8.0 TC IN 50
- 8.1 TC VALUE 51
- 8.2 TC TYPE 51
- 8.3 ARM RECORDING 51
- 9.0 INTERVAL RECORD 51
- 9.1 INTERVAL FRAMES 52
- 9.2 INTERVAL TIME 52
- 13.1 CAMERA DATA 52
- IMPORTANT Notes 53
- About Cameras 53
- Supported by 13.1 53
- IMPORTANT Note 54
- About Using DNxHD 54
- Encoding with 13.1 54
- Camera Data 54
- 32.0 LOSS OF VIDEO 54
- 35.2 REMOTE CONTROL 55
- 41.1 VIDEO SG FRMT 56
- 41.2 VIDEO SG 57
- 41.3 AUDIO SG 57
- 50.1 IP CONFIG 57
- 50.2 IP ADDRESS 57
- 50.3 SUBNET MASK 58
- 50.4 STATIC GATEWAY 58
- 50.5 SYSTEM NAME 59
- 50.6 MAC ADDRESS 59
- 50.9 USER 59
- AUTHENTICATION 59
- 55.4 DATE SET 60
- 55.6 TIME SET 60
- 70.1 SCREEN SAVER 60
- Remote Control Overview 62
- Web Browser via Ethernet 62
- Update Firmware 76
- Upload and Install the 77
- Software on Your Ki Pro 77
- Advanced Features 78
- Gang Recording 80
- Working with the All 81
- Clips Playlist 81
- Creating a Playlist 81
- Playback of a Playlist 83
- Storing a Preset 83
- Recalling Presets 84
- All Clips and Media 86
- State > Data-LAN 86
- Appropriately Encoded 87
- Appendix A: Specifications 88
- Panel User Interface 89
- Timecode 89
- Serial Port 89
- Hardware Conversion 89
- Physical 90
- Canadian ICES Statement 91
- Regulatory Compliance 92
- Taiwan Compliance Statement 93
- Chinese Compliance Statement 93
- Messages 94
- Limited Warranty 108
- Limitation of Liability 109
Related products and manuals for Video capturing devices AJA Ki PRO rack
(82 pages)© 2020, manymanuals.com. All rights reserved. | 0.522 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comments to this Manuals